Author Topic: HM1106 Build Pic's  (Read 11264 times)

Ranman

  • Hurricane Owner
  • *
  • Posts: 349
  • HM1106
    • View Profile
    • Email
HM1106 Build Pic's
« on: September 11, 2007, 01:58:52 pm »
Here are some pic's
 
Windshield frame, lower 3/8 hole drilled, marked inside edge of brass frame to remove the excess that hangs down into the foot box, and upper frame marked for drilling, all set to 37 deg.
« Last Edit: September 11, 2007, 02:56:26 pm by ranman »
427W, TKO600 .82,  3.20 rear, dual hoops

Ranman

  • Hurricane Owner
  • *
  • Posts: 349
  • HM1106
    • View Profile
    • Email
Re: HM1106 Build Pic's
« Reply #1 on: September 11, 2007, 02:04:43 pm »
Windshield wiper holes, 5/8" hole drilled at 45 deg angle.  
Set to 3/8" distance from window trim to finished trim on wiper assembly.
427W, TKO600 .82,  3.20 rear, dual hoops

Ranman

  • Hurricane Owner
  • *
  • Posts: 349
  • HM1106
    • View Profile
    • Email
Re: HM1106 Build Pic's
« Reply #2 on: September 11, 2007, 02:06:03 pm »
Body off frame.
427W, TKO600 .82,  3.20 rear, dual hoops

Ranman

  • Hurricane Owner
  • *
  • Posts: 349
  • HM1106
    • View Profile
    • Email
Re: HM1106 Build Pic's
« Reply #3 on: September 11, 2007, 02:06:33 pm »
Bare frame
427W, TKO600 .82,  3.20 rear, dual hoops

Ranman

  • Hurricane Owner
  • *
  • Posts: 349
  • HM1106
    • View Profile
    • Email
Re: HM1106 Build Pic's
« Reply #4 on: September 11, 2007, 02:07:47 pm »
Brake and Fuel lines ran.
427W, TKO600 .82,  3.20 rear, dual hoops

danc30

  • Hurricane Owner
  • *
  • Posts: 993
  • HM-1073
    • View Profile
    • Email
Re: HM1106 Build Pic's
« Reply #5 on: September 11, 2007, 02:09:13 pm »
Looks good.
« Last Edit: September 11, 2007, 02:12:14 pm by Tazz95 »
KC- Genesis 427-SO, 482-CI - 622 FWHP/630 FWTQ "Almost" too much power.....

Ranman

  • Hurricane Owner
  • *
  • Posts: 349
  • HM1106
    • View Profile
    • Email
Re: HM1106 Build Pic's
« Reply #6 on: September 11, 2007, 02:10:42 pm »
Standard rear brake set up.

Just some info,

Rear has disc brakes, the rotor is remove to torque to axle bearing plate.
Shoes are used for the parking brakes.
« Last Edit: September 11, 2007, 02:54:46 pm by ranman »
427W, TKO600 .82,  3.20 rear, dual hoops

Ranman

  • Hurricane Owner
  • *
  • Posts: 349
  • HM1106
    • View Profile
    • Email
Re: HM1106 Build Pic's
« Reply #7 on: September 11, 2007, 02:28:58 pm »
I love this shot!!!!!!!
427W, TKO600 .82,  3.20 rear, dual hoops

Ranman

  • Hurricane Owner
  • *
  • Posts: 349
  • HM1106
    • View Profile
    • Email
Re: HM1106 Build Pic's
« Reply #8 on: September 11, 2007, 02:45:23 pm »
Thanks Dan,

I will double check that line, when I ran it under the cross bar I had my son jump on the rear frame to simulate driving conditions, looked good at the time, but I will take another look.

This site is great, thanks for the info!!

427W, TKO600 .82,  3.20 rear, dual hoops

danc30

  • Hurricane Owner
  • *
  • Posts: 993
  • HM-1073
    • View Profile
    • Email
Re: HM1106 Build Pic's
« Reply #9 on: September 11, 2007, 03:15:07 pm »
No problem.  Also remember you are probably going to adjust your rear shock springs down a bit to get a good ride height in the back.
KC- Genesis 427-SO, 482-CI - 622 FWHP/630 FWTQ "Almost" too much power.....

Spuddyboy

  • Hurricane Owner
  • *
  • Posts: 384
    • View Profile
    • Email
Re: HM1106 Build Pic's
« Reply #10 on: September 11, 2007, 03:19:45 pm »
Really nice garage!

Did you get the stage I assembly?  I expect mine any day.

Where did you get the plans for the body buck? I thought they were posted here at one time. I like Phil Bernia's Idea too.

Looks Great!

EVan


Ranman

  • Hurricane Owner
  • *
  • Posts: 349
  • HM1106
    • View Profile
    • Email
Re: HM1106 Build Pic's
« Reply #11 on: September 12, 2007, 08:32:26 am »
Evan, thanks for the praise.

Yes, Stage 1 Assy, I really needed it so I could have a rolling car to get up to my garage.
I really am enjoying it, do yourself a favor and go over everything with the build manual, recheck all the items that have been installed (position, torque,ect) it also helps to get intimate with every part of the car, so you know it.

The body buck I got from   www.65shlb.com
Its HM1078, Paul P
He did a get job on the plans, just put the body on right the first time ;D
 I modified them a bit only to lower it so I can work on the body.

Here is a pic of it lowered.
« Last Edit: February 05, 2015, 10:59:06 pm by Paul Proefrock »
427W, TKO600 .82,  3.20 rear, dual hoops

8milebaker

  • Hurricane Owner
  • *
  • Posts: 337
    • View Profile
    • Email
Re: HM1106 Build Pic's
« Reply #12 on: September 12, 2007, 06:43:41 pm »
look like the frame is floating in the rear ?
#1060 289 350hp,48 ida's

danc30

  • Hurricane Owner
  • *
  • Posts: 993
  • HM-1073
    • View Profile
    • Email
Re: HM1106 Build Pic's
« Reply #13 on: September 13, 2007, 09:51:36 am »
I think it is too. We must have very light and well balanced cars..... ;D
Dan
KC- Genesis 427-SO, 482-CI - 622 FWHP/630 FWTQ "Almost" too much power.....

Ranman

  • Hurricane Owner
  • *
  • Posts: 349
  • HM1106
    • View Profile
    • Email
Re: HM1106 Build Pic's
« Reply #14 on: September 26, 2007, 10:32:25 am »
I went with the fuel filler neck on top of the tank, less likely to leak and burp fuel.
Need to cover the pre cut hole for the side mount set up.
427W, TKO600 .82,  3.20 rear, dual hoops